How to Hang Wallpaper: A Step-by-Step Installation Guide

Article author: Nihan Minareci
Article published at: Oct 2, 2026
Article tag: kids' room Article tag: wallpaper Article tag: guide Article tag: installation
An installer presses the seam of cloud-pattern wallpaper and a yellow star onto the wall with his palms | Craft Paper Co

Short answer: The secret to hanging wallpaper isn't the paste, it's the preparation. A wall that is dust-free, sound and evenly absorbent, a paste that matches your type of paper, and a first roll set against a perfectly vertical guide line make up eighty percent of the job. With non-woven papers you can apply paste either to the wall or to the back of the paper; paper-backed wallpapers need to be pasted and left to soak; self-adhesive ones need no paste but are the least forgiving. On a freshly painted wall, wait at least one week; we recommend two.

The two most common reasons wallpaper comes away later are a paste that doesn't suit the paper and the wall paint and a problem surface with no primer (oil-based paint, silicone paint, or a chalky or very absorbent wall). When you buy paste, tell the seller your type of paper and your wall paint and ask whether it's suitable; on a problem wall, apply a wallpaper primer a few days before installation.

Know your paper first — the method depends on it

The reason the answers to this question so often contradict each other is simple: there are four different kinds of wallpaper on the market, and each one asks for something different.

Non-woven (fleece-backed). Most wallpaper sold today is this type. Its backing is a blend of cellulose and textile fibers; it doesn't expand when wet and doesn't change size as it dries. That makes it the easiest paper to install: you can paste the wall and hang the dry paper straight onto it. The paper we use belongs to this family.

Paper-backed (traditional wallpaper). You paste the back of the paper, fold it and let it rest for a few minutes — this is called the "soaking time." The paper expands during this time; if you hang it without letting it rest, it keeps expanding on the wall and bubbles.

Vinyl / embossed. The surface is coated in plastic, so it doesn't breathe and causes trouble on a damp wall. It's heavy, and the seams are more visible.

Self-adhesive. No paste; the back works like tape. Handy on small surfaces, but once it sticks it's hard to reposition, and it won't hold on a rough wall. If you're covering a large wall on your own, this is the most demanding option.

If you don't know which one you have, check the roll's packaging: if it says "non-woven," "vlies" or "fleece-backed," you're in the first group.

The wall: the most skipped step, and the most regretted

Wallpaper doesn't hide the flaws of the surface underneath — it usually magnifies them. Before you start:

  • Remove the dust. Plaster dust stops the paste from gripping. First a dry brush, then a slightly damp cloth.
  • Fill cracks and holes, sand them once dry, then dust again.
  • Even out the absorbency. New plaster, patched spots and painted surfaces absorb differently, and the difference shows up as uneven sheen at the seams. On very absorbent surfaces, a primer or diluted paste is a must.
  • Strip old wallpaper. Papering over it is the shortcut, but when the paste wets the old paper, both can come away together.
  • Don't hang onto a damp wall. A wall with a moisture problem will always cause trouble; wallpaper doesn't cover it up, it only delays it.
  • If the paint is new, wait. Paint takes days to cure fully. Wait at least one week; we recommend two. The risk on a rushed wall: the paint comes off with the paper during removal or as the paper tensions while drying.
Drawing of the wall-preparation step: bunnies and a roll in an empty room
First, an empty, prepared wall. Drawing: Nihan Minareci

Wallpaper primer: the fix for most problems that start with the wall

Wallpaper primer is an inexpensive product you apply with a roller or brush, like paint. Its job is to create an even, sound surface the paste can grip between the wall and the paste. Most of the problems we see most often in the field, "the paper fell off," "a seam opened," "it's shiny in one spot and matte in another," come from the wall itself, and primer solves most of them from the start.

Which walls need primer?

  • Old oil-based and glossy paints. The surface is slippery and doesn't absorb water, so a water-based paste has nothing to grip. The paper looks stuck on the first day, then can lift at the edges as it dries.
  • Silicone and "washable" interior paints. Surfaces made to repel stains can repel paste too. The same happens with some newer paints.
  • Chalky walls that leave your hand white. Whitewash, lime or weak paint: if the paste grips the paint but the paint doesn't grip the wall, the paper comes down together with the paint.
  • Very or unevenly absorbent surfaces. Walls with new plaster, filler patches and painted areas side by side. The paste is soaked up instantly in one place and stays wet in another; this is where seams open most.

When should you apply it?

Follow the drying time on the primer's packaging. In our experience, primer applied 4–5 days before installation gives the wall enough time. Think of primer as a coat of paint; primer that's rushed on and papered over the same day can cause problems instead of helping.

What primer does for you

  • The paste grips the primer, not the wall; even on oil-based or silicone paint, the paper has a base to hold on to.
  • Every part of the wall absorbs at the same rate; the paste dries evenly and the seams don't open.
  • The paper stays slidable on the wall, which makes it easier to match the pattern.
  • If you ever want to take it down, the paper comes off more cleanly and the paint and plaster underneath suffer less damage.

Ask a paint retailer who knows your wall paint, or your installer, which primer suits your wall. Our advice: if you're not sure what paint is on your wall, don't skip the primer. The cost of primer is tiny next to the cost of wallpaper that falls off.

What you'll need

Tape measure and pencil · laser level · non-woven wallpaper paste · paste brush or roller · smoothing tool (plastic smoother) · fine-tipped wallpaper knife and spare blades · steel straightedge · seam roller · clean sponge and cloth.

If you're tempted to shorten the list, don't; the two tools that cause the most problems are the laser level and sharp knife blades. A dull blade doesn't cut the paper, it tears it.

Paste: which one, how much, and where?

If your paper is non-woven, buy non-woven wallpaper paste; mixes sold as "suitable for all papers" are usually formulated for paper-backed wallpaper.

Why don't old-style powder pastes hold on every paper?

Some of the powder pastes used for years were developed for thin, paper-backed wallpapers. Some of these pastes don't work well with today's heavy non-woven papers and newer wall paints. The result usually shows up not on installation day but a few days or weeks later: the paper lifts at the edges, seams open, and in the worst case a panel falls off the wall. The paste an installer says they "always use" may not suit your paper and your wall.

Ask the seller when you buy paste

  1. Is this paste suitable for non-woven paper?
  2. Will it hold a heavy paper like 300 gsm?
  3. My wall paint is this (silicone, satin, old oil-based paint…); will it hold on this surface, or do I need a primer first?
  4. How many liters of water does one packet mix with, and how many square meters does it cover?

The mixing ratio isn't on every packet. The powder pastes sold in Türkiye often don't state the water ratio or which paper they suit, either on the packet or on the product page; when we looked at the page for a 250 g powder paste on a large home-improvement store's website, we couldn't find either. Ratios also vary a lot from brand to brand: one non-woven paste is sold at about 35 m² (about 375 sq ft) per 200 g packet, while with the paste our installer uses, 250 g covers about 25 m² (about 270 sq ft). So read the measure below as an example, not a fixed rule; for your own paste, follow the instructions on the packet and the seller's advice.

Example measure (our installer's paste). A 250 g packet of powder paste is mixed with 6–6.5 liters (about 1.6–1.7 US gallons) of water and covers roughly 25 square meters (about 270 sq ft).

How to mix it. Water first, then powder. Sprinkle the powder over the water a little at a time; tipping it all in at once is the quickest way to get lumps. Our installer mixes it with the handle of a pair of scissors: it spins like a whisk, every home has one, and it really disperses the powder through the water. A wooden spoon or a straight stick doesn't do the same job; the paste just collects around it. After mixing, let it rest for about 10 minutes; once the consistency has settled, it's ready to use.

If you're buying ready-mixed (liquid) paste, reading the label isn't enough; ask the seller two questions: how many square meters of non-woven paper does this paste hang, and is its consistency right for a 300 gsm paper? A runny paste made for lightweight papers won't hold a heavy one.

Where does it go? Technical data sheets allow both for non-woven: the paste can be applied straight to the wall, or to the back of the paper. In practice, most installers paste the back of the paper and then wipe what's left on the brush onto the wall near the corners and edges. The reason is simple: when the back of the paper is evenly wetted, the roll settles onto the wall more obediently, and since corners and edges are where paste dries fastest and seams open most, a little extra paste there helps.

Whichever you choose, two rules don't change: apply it thin and even, and keep paste off the front of the paper. If some gets on, wipe it off before it dries with a clean, damp sponge.

The installers' trick: booking. Pasted paper needs to rest for a few minutes; the paste works into the paper, the paper softens and it settles onto the wall better. Good installers don't waste that time: they loosely fold the pasted panel with the pasted sides facing in, set it aside and paste the next panel in the meantime. By the time its turn comes, the first panel has had its 3–4 minutes, rested and softened; they unfold it and hang it. Don't press down on the fold, or the paper will crease. If you won't use this folding method, paste only one panel at a time.

Drawing of paste applied to the back of a wallpaper panel
Paste on the back of the paper, thin and even, corners and edges included. Drawing: Nihan Minareci

Powder paste is sprinkled into the water and mixed with the handle of a pair of scissors.

Paste is spread thin and even on the back of the paper.

The starting line: from a plumb line, not from the corner

Corners in homes are never perfectly square. If you hang the first roll tight against the corner, that tilt grows across the wall and shows up as a gap of a few centimeters (an inch or more) at the last roll.

The right way: from one end of the wall, mark a point a few centimeters less than the width of the first roll and use a laser level to project a perfectly vertical line. The edge of the first roll lines up with this line, not with the corner. The excess at the corner is trimmed afterwards.

The first roll and the smoother

Hold the roll at the top, line it up with the guide line and let it down, leaving a few centimeters (an inch or two) of excess at the top and bottom. Then smooth from the center outwards: first from the center up, then from the center down, then out to the sides. Air and excess paste escape at the edges.

A bunny hanging the first cloud panel on the wall from the top down
The first panel comes down from the top under its own weight; don't stretch or pull it. Drawing: Nihan Minareci

Don't rush with the smoother; while the paper is wet, its surface can scratch. If a bubble stays, don't prick it with a needle — gently lifting the edge and laying it down again almost always gives a cleaner result.

From the second roll on, there's one more job: matching the pattern. Before the roll is fully settled, while the paper can still slide, line the pattern up with its counterpart on the neighboring roll so the design carries on unbroken across the seam. While the paste is wet, the paper can be slid a few millimeters; once it dries, it can't — which is why matching is done while it's wet.

Hanging from start to finish: the roll comes down from the top, the top edge is lined up with the ceiling line, and the pattern is matched to the next roll.

Smoother from the center out: up first, then down, then to the sides.

Seams: butt joint or overlap and double cut?

There are two methods, and which one is right depends on your wall.

Butt joint (no overlap). Two rolls are placed side by side without overlapping. If the factory-cut edges are clean and the wall is plumb, this is the quickest method. The risk: even the slightest shrinkage as it dries opens a thin line at the seam, and if light hits the wall from the side, that line shows.

Overlap + double cut. The two rolls are overlapped by a centimeter or two (about half an inch to an inch); then, guided by a steel straightedge, you cut down the exact middle of the overlap through both layers in one pass. The excess strips on top and underneath are removed and the seam is pressed down with a seam roller. That way both edges come from the same blade line and meet to the millimeter. Professionals prefer this method for high-contrast patterns, for scenic and mural-style prints, and on walls that aren't plumb.

Three details make or break a double cut: change the knife blade for every cut, place the straightedge once and don't lift it until the cut is done, and don't press the blade too hard into the wall — the goal is to cut the paper, not to score the plaster.

Two-stage drawing: double cut through the middle of the overlap and the closed seam
Left: cutting through both layers down the exact middle of the overlap. Right: the seam closes once the strips are removed. Drawing: Nihan Minareci

A double cut from start to finish: the blade runs down the middle of the overlap, the excess strips come away, and the seam is pressed down with the smoother.

Two rolls are overlapped and cut through both layers down the middle of the overlap.

Points to watch when cutting

  • The knife blade must be very fine. A thick blade can tear the paper and make the seams visible.
  • Change the blade for every panel.
  • If you're inexperienced, use a metal straightedge or a metal spatula as a guide while cutting, so the blade doesn't stray outside the overlap.
  • Don't press the blade into the wall. If the paint, or even the plaster, is cut, paste fills the cut and the seam may open there later.
  • The pressure should be neither too much nor too little: the paper gets cut, the wall doesn't.
  • At the very bottom, hold the knife the other way round and support the paper from below with your other hand.

On patterned papers, the overlap also helps you match the pattern: the two rolls are laid one over the other, the pattern is lined up, and only then is the cut made.

The pattern is matched exactly at the seam.

The seam between two rolls of gray-cloud wallpaper being smoothed by hand, with a yellow star figure beside it
After cutting, the seam is pressed down with the palm. With a well-made double cut, the seam is very hard to find afterwards.

Drying: the last step people rush

Once the last panel is up, trim the excess at the ceiling, baseboard and corners with a steel straightedge and a knife with a fresh blade, and wipe off any paste marks with a damp cloth.

Trimming the excess at the bottom edge of a panel along the baseboard
The excess at the baseboard is trimmed along a straightedge. Drawing: Nihan Minareci

When the hanging is done, the job isn't over. How fast the paste dries decides whether the seams open or not.

  • Let it dry slowly, at room temperature. Eighteen to twenty degrees Celsius (about 64–68 °F) is ideal.
  • Don't open doors and windows to speed up drying. An open window dries the paste fast in one spot and slowly in another; that's where the seam opens.
  • If there's a radiator on the same wall, turn it down or off for the first day.
  • Don't let the air conditioning blow straight onto the wall.
  • Don't open the balcony door, a window or the air conditioning to air the room; let the room dry on its own. If it's a nursery, it's best for the baby not to sleep in that room during these two days.
Finished kids room; white-cloud wallpaper on a light navy background with cream curtains
The same room finished: clouds on a light navy background, with the same design turning yellow on the opposite wall.

Eight common mistakes

  1. Starting from the corner instead of drawing a guide line.
  2. Not removing all the dust — the most common reason wallpaper doesn't stick.
  3. The wrong paste; assuming an "all papers" product is right for non-woven, and not asking the seller whether it suits your paper and paint.
  4. Hanging over oil-based, silicone or chalky paint without a primer.
  5. Applying the paste thickly. Thick paste doesn't hold better; it just dries late and oozes out at the edges.
  6. Cutting with a dull blade.
  7. Not waiting after painting the wall.
  8. Trying to dry the room quickly.

Frequently asked questions

Can I do it myself?

On a small wall without interruptions, yes, though it still takes a little experience. If the rolls are longer than two meters (about 6.5 ft), a second pair of hands makes the job easier and keeps the paper from stretching under its own weight.

Should I hire an installer, and what should I look for?

With a patterned, made-to-measure wallpaper, an installer's experience makes a difference. Before you agree, ask three things: have they hung patterned, pattern-matched paper before, do they overlap and double cut the seams, and is wall preparation included in the price. Prices vary a lot by area and by the condition of the wall, so we don't give a figure here.

How much paste should I buy?

The ratio varies from brand to brand; follow the instructions on the packet and the seller's advice. As an example, with the paste our installer uses, a 250 g packet is mixed with 6–6.5 liters (about 1.6–1.7 US gallons) of water and covers about 25 square meters (about 270 sq ft). For a single wall, one packet is usually enough.

Can you hang wallpaper over oil-based or silicone paint?

Yes, but apply a wallpaper primer first. These surfaces are slippery and water-repellent, so the paste can't grip them directly, and the paper can lift once it dries. Applying the primer 4–5 days before installation usually gives it enough time; check the drying time on the packaging too.

Which wallpaper paste should I buy?

One that suits your type of paper (non-woven, paper-backed, vinyl), its weight and your wall paint. Some old-style powder pastes don't work with heavy non-woven papers and newer paints. When you buy, tell the seller the type of paper, its weight and your wall paint, and ask whether the paste is suitable.

Can I hang wallpaper over old wallpaper?

It isn't recommended. The new paste wets the old paper and both can come away together.

What about outlets and switches?

Turn off the power, remove the cover plates, hang the paper over them and cut once it's dry. When the cover goes back on, the cut edge isn't visible.

How do I go around corners?

Don't wrap a corner with a single piece. Cut the paper so it runs a centimeter or two (about half an inch to an inch) past the corner, and continue on the next wall from a new guide line.

How long does it take to dry, and when can I push furniture against it?

The surface feels dry within a few hours, but you need to wait two days for the paste to set fully. Wait the same time before pushing furniture against the wall.

What's different about our wallpaper?

Everything above applies to any wallpaper. With Craft Paper Co. wallpaper murals, a few details make the job easier:

  • The paper is a 300 gsm lightly textured non-woven — in other words, from the "easiest" group above.
  • Your wallpaper is produced 5 cm (2 in) larger on every edge than the measurements you give us, left to you as a trimming and alignment allowance.
  • The rolls are printed with a 2–2.5 cm (about 1 in) overlap, so they arrive ready for the double-cut method above. Once the job is done, the seams are very hard to see.
  • The layout template in the box shows the order and direction of the rolls, so you don't have to work out which roll goes where.
Finished kids room; white-cloud wallpaper on a yellow background, with a white baseboard below
The same design turns yellow on the opposite wall of the same room. The design is produced to the wall's own measurements.

If you'd like to see the whole installation in one minute:

From the layout plan to the last roll: one room, start to finish.

For step-by-step instructions specific to our product, see our Installation Guide. If you haven't measured your wall yet, start with the How to Measure Your Wall guide; to choose a design, browse our ready-made designs; and if you ever need to take it down, our how to remove wallpaper article is here.

Browse kids room wallpaper murals hand-drawn by Nihan Minareci and made to the size of your wall.

Browse the wallpaper murals

Sources we relied on for this article

  • Henkel / Metylan — non-woven wallpaper paste technical data sheet (pasting the wall or the back of the paper, coverage, dilution on absorbent surfaces)
  • Erfurt — non-woven paste technical data sheet (mixing, resting time, working temperature range)
  • Hovia — professional print installation guide (overlap allowance and double cut, radiator on the first day)
  • Craft Paper Co. How to install wallpaper murals and wall decals
Share